Following the success of summer-camp-based programs, a new program has been developed for in-school sessions focused around LEGO robotics to foster interest in STEM topics at a young age. The program has been implemented in a very diverse school, and preliminary results on the efficacy of the program are presented. (Contains 1 table and 6 figures.)

Last month, Rodger Bybee's article, "Scientific and Engineering Practices in K-12 Classrooms," provided an overview of Chapter 3 in "A Framework for K-12 Science Education: Practices, Crosscutting Concepts, and Core Ideas" (NRC 2011). Chapter 3 describes the practices of science and engineering that students are expected to develop during 13 years…

The strengths and weaknesses of the discipline-based organization of our professions can help us understand both the enormous successes of our civilization and its equally spectacular failures. Placing engineering and other professions under greater public scrutiny is recommended as a first step toward addressing our deep structural economic,…

The Department of Electronics of the Technological Educational Institute of Crete (DoE/TEI Crete) enjoys good approval ratings from the market and its graduates have a high rate of employability. However, survey data collected over the last ten years from graduates and from the enterprises in which they have been employed, or have carried out…

A cost-effective, hands-on laboratory exercise is described for demonstrating nanoscale fabrication at non-research-based educational institutions. The laboratory exercise also contains a component involving qualitative and quantitative surface characterization of student-fabricated nanoscale structures at institutions with on-site access to an…

Continuous feed and bleed ultrafiltration, modeled with the gel polarization model for the limiting flux, is shown to provide a rich source of non-linear algebraic equations that can be readily solved using numerical and graphical techniques familiar to undergraduate students. We present a variety of numerical problems in the design, analysis, and…

Pre-engineering is increasingly being taught as a high school subject. This development presents challenges as well as opportunities for the physics education community. If pre-engineering is taught as a separate class, it may divert resources and students from traditional physics classes. However, design modules can be used as physics teaching…

Since technology education is, compared to subjects such as mathematics and science, still a fairly new subject both nationally and internationally, it does not have an established subject philosophy. In the absence of an established subject philosophy for technology education, one can draw on other disciplines in the field, such as engineering…

This paper describes a laboratory project consisting of a PC power supply modification into an intelligent car-battery conditioner with both wireless and wired networking capabilities. Adding a microcontroller to an average PC power supply transforms it into a flexible, intelligent device that can be configured and that is suitable to keep car…

This study examines the use of an engineering design and information systems case study over a three week period in a senior level class covering the topics of product data management (PDM) and product lifecycle management (PLM). Students that have taken the course in the past have struggled with the sometimes nebulous and difficult to…

This article describes the "Kick Stick" activity from Design Squad Nation, in which kids turn a wooden paint stirrer and circuit into a motorized, spinning arm--then use it to kick a Ping-Pong[R] ball across the floor. Teachers can enrich their students' exploration of circuits and emphasize the engineering design process with "Design Squad…

Energy modeling can be a powerful tool for managing energy-reduction concepts for an institution. Different types of energy models are developed at various stages of a project to provide data that can verify or disprove suggested energy-efficiency measures. Education institutions should understand what an energy model can do and, more important,…

In this paper, a short introductory course to introduce field-programmable gate array (FPGA)-based digital control of dc/dc switching power converters is presented. Digital control based on specific hardware has been at the leading edge of low-medium power dc/dc switching converters in recent years. Besides industry's interest in this topic, from…

A lightweight Web Service and a Web site interface have been developed, which enable remote measurements of electronic devices as a "virtual laboratory" for undergraduate engineering classes. Using standard browsers without additional plugins (such as Internet Explorer, Firefox, or even Safari on an iPhone), remote users can control a Keithley…

This paper describes an adjustable speed drive for a three-phase motor, which has been implemented as a design for a servo system laboratory course in an engineering curriculum. The platform is controlled and analyzed in a LabVIEW environment and run on a PC. Theory is introduced in order to show the sensorless algorithms. These are computed by…